Good soap starts with a scale you can trust, a thermometer that tells the truth, and tools that never wander back into the kitchen drawer. This module teaches you to choose each tool by the numbers, check it, and know when to retire it. It builds on Module 2's lye-safe materials and personal protective equipment (PPE) rather than repeating them.
What you'll learn
- LO3.1 Choose a digital scale with suitable capacity and resolution, and check it with a known weight.
- LO3.2 Select lye-safe materials (stainless steel, HDPE/PP #2 and #5 plastics, heat-resistant glass caveats) and identify reactive metals to avoid.
- LO3.3 Equip a soap kitchen with dedicated tools, thermometers, stick blender and moulds.
- LO3.4 Keep soapmaking equipment separate from food use and label it.
The scale: your most important tool
Every amount in a recipe is a weight; the shop calculator says to weigh exactly what its weigh-out shows [S1].
Capacity, readability and minimum load
- Capacity (Max): the heaviest load the scale can weigh [S153].
- Readability (d): the step between two displayed values, such as 1 g, 0.1 g or 0.01 g [S153]. Legal metrology also uses e, the verification interval the manufacturer specifies for testing; on most scales e equals d [S153][S154]. If yours doesn't state e, treat d as e.
Readability isn't accuracy, and rounding alone can be off by half a division. Weighing standards also define a minimum capacity, the load below which results may carry an excessive relative error [S154]. Canada's specification for trade scales sets a minimum net load of 20 e for general uses of scales with steps from 0.1 g to 2 g [S153]. The international recommendation OIML R 76 uses 20 e for high-accuracy (0.001–0.05 g) scales too [S154]. This course makes 20 divisions your rule for every scale.
| Readability | Minimum load (20 e) | Rounding error on 5.0 g |
|---|---|---|
| 1 g | 20 g | ±10% |
| 0.1 g | 2 g | ±1% |
| 0.01 g | 0.2 g | ±0.1% |
Minimum loads [S153][S154]; rounding is half a division as a share of the load.
Tare, capacity and units
Tare zeroes the display with the container on. It doesn't add capacity: the container still sits on the scale.
Work in grams. Canada defines the pound as exactly 0.45359237 kg and the ounce as one-sixteenth of a pound [S152], about 28.35 g. A 0.05 oz display step is about 1.42 g, coarser than a 1 g display. Lock the scale in grams.
Checking your scale
Measurement Canada tells trade-scale owners they are legally responsible for accuracy and should install scales properly, protect them from interference and check them daily [S159]. Copy that habit:
- Set-up: install it properly and protect it from interference [S159]. In this course that means a level, solid surface away from drafts, vibration and the lye zone.
- Sensitivity: weigh a known test mass near the top of the range, and at your working loads.
- Repeatability: weigh the same item several times; the readings should agree.
- Corners (eccentricity): weigh one mass in the centre, then near each corner; the reading shouldn't change.
These three checks are course practice. A trade-magazine article on weighing uncertainty names repeatability, eccentricity, nonlinearity and sensitivity as the main properties that limit a scale [S160].
Use a real test mass. Calibrated weights follow OIML R 111 classes. A 100 g class M1 weight is within ±5 mg; class M3 within ±50 mg [S155]. M-class weights are intended for medium-accuracy (class III) scales and F-class for high-accuracy (class II) scales, and a test weight's error should not exceed one-third of the scale's permitted error [S155].
How close is close enough? A kitchen scale isn't inspected for trade use, but Canada's trade limits are a good yardstick. For class III scales the in-service limit is ±1 e up to 500 e, ±2 e from 500 to 2,000 e and ±3 e from 2,000 to 4,000 e; new devices must meet half those values [S153].
Coins are only a rough check. The Royal Canadian Mint Act sets 6.27 g for the multi-ply plated steel $1 coin and 6.92 g for the multi-ply $2, but also lists older specifications for the same coins, such as a 7.0 g $1 [S156]. Tolerance is per kilogram of a counted batch, not per coin: ±30.4 g per kilogram of 160 $1 coins, or ±3.04% [S156]. On one $1 coin that's about ±0.19 g, nearly two divisions on a 0.1 g scale; ten coins (62.7 g) carry about ±1.9 g. A coin can show that a scale is badly wrong. It can't prove a 0.1 g scale is right.
What a scale error does to your lye
Your superfat is the safety margin; keep it above 1% [S1].
Selling by weight: legal-for-trade scales
Under the Weights and Measures Act, trade means selling or providing a commodity on the basis of measure, and a trader may not use a device in trade unless its type is approved and the device has been inspected [S152]. Measurement Canada staff or an Authorized Service Provider inspect and certify such devices [S159].
| How you use the scale | Status |
|---|---|
| Weighing oils, lye and water for a recipe | Batching ingredients is not trade (Measurement Canada's examples: ice cream ingredients, feed) [S158] |
| Checking bars that all declare the same weight, e.g. "110 g" | A lot with identical net quantity statements is a standard quantity commodity [S157]; a device used exclusively for these is exempt from approval and inspection [S157][S158] |
| Cutting soap to order and pricing by weight, or labelling each bar with its own weight | Individually measured quantities are trade, so the scale must be approved and inspected [S158] |
The exemption needs the scale to be used only for identically labelled packages [S157]; a scale that also prices loose soap needs approval. It covers the device, not your label: the declared net quantity must still be right (Module 18) [S54]. Contact Measurement Canada before selling by weight.
Thermometers
Lye solution gets very hot: a soapmaking supplier reports up to about 93 °C (200 °F) [S20], and the manufacturer's handbook warns it can boil in spots [S6]. Plan your thermometer and containers for that range (Module 10 covers targets).
Probe thermometers: choose a stainless stem, since 304 and 316 stainless are acceptable with caustic soda up to 93 °C (200 °F) [S5]. Stir first, keep the tip off the bottom and sides, and wait for the reading to settle [S162].
Infrared (IR) thermometers read only the surface, which may differ from the core [S161][S164]. Polished metal has low emissivity: it reflects the room's infrared instead of emitting its own, so a stainless pot of boiling water can read about 38 °C (100 °F) [S164][S165]. Never judge lye in a stainless pot with an IR gun; stir and confirm with a probe. Australian and New Zealand food regulators require thermometers accurate to ±1 °C and don't accept IR alone [S161], a sensible standard for soap too.
Ice-point check. Fill a glass with crushed ice, add just enough water to make a slurry, and stir. Hold the probe in it without touching the glass and wait for the reading to settle: it should show 0 °C (32 °F) [S162][S163]. Adjust it if your model allows; not all digital thermometers can be adjusted [S162]. Check before first use, after a drop or a big temperature swing, and at least monthly [S162][S163].
The stick blender
Choose a stainless steel shaft and bell (the blade guard): 304/316 stainless is on Module 2's lye-safe list [S5], and metal is easy to inspect. Plastic heads absorb fragrance [S174].
Burp it. Air trapped under the bell becomes bubbles in your soap. Before switching on, tap or tilt the submerged blender until the air escapes [S170]. Keep the head down with the jets covered, and blend in short bursts with hand stirring between [S171]. Pour lye solution down the shaft rather than splashing it in [S170].
Containers, spatulas and whisks
Module 2's rule stands: polypropylene (PP, resin code 5), high-density polyethylene (HDPE, code 2) or 304/316 stainless; never aluminium, zinc, tin, copper, brass or bronze [S5][S19].
Heat matters as much as chemistry. OxyChem says polyethylene, polypropylene and PVC resist caustic soda only within their temperature limits [S5]. Thermo Fisher gives maximum use temperatures of 135 °C for PP, 120 °C for HDPE, 80 °C for low-density polyethylene (LDPE, code 4) and 70 °C for PETG, rates PP and HDPE undamaged after 30 days in 50% and pure sodium hydroxide at 20 °C and 50 °C, and notes resistance falls as temperature rises [S169]. With lye near 93 °C [S20], PP and HDPE have headroom; LDPE and PETG don't. Buy thick, rigid jugs with the resin code moulded in [S19].
The glass rule. Alkaline solutions attack all glass, and a laboratory glass maker rates even borosilicate as only moderately resistant [S353]; a caustic soda maker specifies non-glass tubes for metering lye [S5]. One soapmaking educator warns that etched glass may eventually shatter [S22]; this course does not rest the rule on that single claim. Some suppliers still accept heat-resistant glass for lye [S20][S171]. This course's house rule is stricter than those suppliers: no glass for lye, only PP, HDPE or stainless.
Other metals and coatings. Avoid iron and cast iron too [S171][S174]. CCOHS lists carbon steel among the metals sodium hydroxide corrodes [S2], warm caustic picks up iron [S5], and dissolved iron speeds orange spotting [S92]. Skip non-stick (Teflon) coatings [S171].
Spatulas and whisks. Use silicone or PP spatulas and stainless whisks; wooden spoons deteriorate [S171].
Inspect before every session. Thermo Fisher tells lab users to check plastic before each use for cracking, crazing (fine spiderweb cracks), permanent discolouration and embrittlement, and to replace it when they appear. Detergents, surfactants and oils can drive stress cracking [S169], and soap is all three. Check stainless for pitting.
Moulds and cutting tools
Module 13 covers these in depth. Which moulds are safe:
| Mould | What to know |
|---|---|
| Silicone | Flexible, needs no lining, withstands high heat [S172]. Batter only: Module 2's list doesn't include silicone for lye solution. |
| Wood | Must be lined, for example with freezer paper. Use untreated hardwood; treated wood can react with unsaponified soap [S172]. |
| HDPE and rigid plastic | Lye-resistant [S5][S169]; can be hard to release if the soap didn't gel [S172]. |
| PVC pipe | Round soap, no liner needed, mineral oil helps release [S172]. Thermo Fisher rates its PVC tubing to only 71–82 °C [S169], and PVC resists caustic only within its limit [S5], so never oven-heat it. Caustic attacks the silica filler in PVC glue [S5]; use push-on end caps, not glued joints. |
| Aluminium or foil-lined | Never: aluminium reacts with lye [S2][S4]. |
Cutting. A straight knife, or a wire cutter drawn slowly, gives clean bars [S171]. Fresh soap is still caustic, so wear gloves (Module 2) [S20][S21].
Dedicated equipment: separate, labelled, stored
Every tool that touches lye or raw soap belongs to soapmaking for life. Raw soap stays caustic until it saponifies [S20][S21], and plastic absorbs fragrance [S174]. CCOHS warns that empty sodium hydroxide containers may hold hazardous residue even when they look clean, and must never be reused [S2]; Health Canada says never to re-use empty chemical containers [S16] or put chemicals in beverage containers [S17]. One educator says stainless can return to cooking after thorough cleaning [S174]. This course takes the safer line and dedicates everything.
Cleaning. Keep gloves and goggles on: traced soap is still caustic [S20][S173]. Wipe out raw soap with paper towels (it can clog drains), then wash with hot water and dish soap, or leave wiped items somewhere safe for a few days until the residue turns to soap [S20][S173]. Clean blender blades by running them in hot water, switched on only while submerged [S173]. Never put oily towels in a dryer: they can self-heat and catch fire (Module 4) [S100][S101].
Safety equipment
PPE. Module 2 sets the standard: indirect-vented splash goggles, chemical-resistant gloves, long sleeves, apron and closed shoes [S8][S2], plus disposable nitrile gloves for scent oils (Academy house rule). Replace scratched goggles and torn gloves.
Eyewash. Running water within seconds is your eyewash; bottles only supplement it [S9].
Fire extinguisher. For a pot fire, slide a metal lid over the pan, turn off the burner, and never use water (Module 4) [S96][S97]. BC's fire safety guide calls ABC extinguishers an excellent home choice, wants one in the kitchen, inspected monthly, and lists cooking oil under Class B. It also says only wet chemical extinguishers suit Class K cooking-oil fires, and that spray can knock over pots and spread a stove fire [S176]. Toronto Fire says to look for the ULC label, mount it near an exit away from the stove, and call 9-1-1 first, however small the fire [S175]. Fight a fire only if it's small and your escape route is clear [S175][S176]. Sources differ on ABC for cooking oil, so: lid first, ABC as your general unit, and get out if the lid fails.
First aid kit. The Canadian Red Cross lists dressings, tape, bandages, scissors, tweezers, cold packs, non-latex gloves and emergency numbers including 1-844-POISON-X; check it every six months and restock after use [S177]. For lye on skin or eyes, water comes first, for at least 60 minutes [S2].
Equipment checklist
| Item | Look for | Priority |
|---|---|---|
| Main scale | 0.1 g, 3–5 kg, gram mode | Essential |
| Fine scale | 0.01 g for tiny test batches | Later |
| Test mass | 100 g or 500 g, OIML M1 or better | Essential |
| Probe thermometer | Stainless stem, 0–100 °C at least | Essential |
| IR thermometer | Adjustable emissivity helps | Optional |
| Stick blender | Stainless shaft, electrical safety mark | Essential |
| Lye and mixing jugs | Thick PP (5) or HDPE (2) | Essential |
| Stainless pot | 304/316 | Essential |
| Spatulas, whisk, spoons | Silicone, PP, stainless | Essential |
| Mould | Silicone loaf, about 1 kg | Essential |
| PPE | Chemical-splash goggles (sealing, uncracked), chemical gloves, disposable nitrile gloves for scent, apron | Essential |
| Fire extinguisher | ABC, ULC label | Essential |
| First aid kit | Red Cross list | Essential |
| Labels and lidded bin | "SOAP ONLY" | Essential |
Before each session: scale checked and in grams; thermometer checked; containers and cord inspected; GFCI outlet; extinguisher inspected; sink path clear; food away.
Scenario: putting it together
Your 100 g test mass reads 98.0 g on your 0.1 g scale: 2% low, ten times the ±0.2 g yardstick [S153]. You weigh the lye on it anyway and the oils on a separate, correct scale. The displayed 137.8 g is really about 140.6 g, so your superfat falls to about 3.1%. Most of the margin for SAP variation (Module 4) is gone. Stop, recheck on a level surface, and replace the scale if it still fails. Never "correct" a faulty scale in your head on lye day.
Key terms
- Readability (d) / verification interval (e): the smallest displayed step / the manufacturer's test interval, usually equal.
- Minimum load: the smallest load worth weighing; this course uses 20 e.
- Test mass: a weight of known OIML R 111 class used to check a scale.
- Standard quantity commodity: one of a lot with identical net quantity statements.
- Emissivity: how well a surface emits infrared; shiny metal is low.
- Ice-point check: a probe in ice slurry should read 0 °C.
- GFCI: a device that cuts power when a shock hazard develops.
- Crazing: fine spiderweb cracks in plastic; retire the item.
Summary
- Size capacity for container plus batch; weigh nothing below 20 divisions; use 0.1 g for fragrance and colourant [S153][S154].
- Check the scale each session with an OIML-class test mass, not coins [S155][S156][S159].
- A lye scale reading 2% low cuts a 5% superfat to about 3.1% [S1].
- Pricing soap by weight needs an approved, inspected scale; one used only for identically labelled packages is exempt [S152][S157][S158].
- Use a stainless probe and check it at the ice point; IR reads only surfaces and misreads shiny stainless [S161][S162][S164].
- Use a stainless stick blender, burp it, keep it dry and plug it into a GFCI outlet [S166][S167][S170].
- Use thick PP, HDPE or 304/316 stainless; retire anything cracked, crazed or pitted [S5][S169].
- Dedicate and label every soap tool for life [S2][S16].
- Keep a clear sink path, an ABC extinguisher and a first aid kit [S9][S176][S177].