Skip to content

Cart

Your cart is empty

Island Enchantments Academy

Module 1 · Foundations · Free

Hot Process and Cold Process: What Changes

You already make cold process soap. Hot process uses the same oils, the same lye, the same calculation and the same safety rules. The difference is what happens after trace: instead of pouring the batter into a mould and letting the reaction finish there, you keep it hot in a pot until the reaction has finished, and then mould it. That one change affects the water, the texture, the timing of fragrance and superfat, the design possibilities, the hazards and the records. This module sets out what changes and what does not, so you can decide whether hot process is for you before you buy anything.

The course assumes you have done the Cold Process Soapmaking Course, especially Modules 1, 2, 5, 6, 9, 14 and 15. It is strongly recommended, though not required: everything safety-critical is restated here, and Module 2 of this course is a safety gate you must pass at 100%.

What you'll learn

  • LO1.1 Explain hot process as the cold process reaction with heat applied after trace so that saponification finishes in the pot before moulding.
  • LO1.2 Compare hot and cold process for timing of saponification, water, texture, design, fragrance and superfat timing, cure and records.
  • LO1.3 Identify what carries over unchanged from the Cold Process Soapmaking Course: the lye calculation, the 1% superfat floor, the safety rules, the discard rules and the regulatory duties.
  • LO1.4 Explain why cooked soap is not automatically milder or safe to use, and why this course never uses the zap test.
  • LO1.5 Decide when hot process suits a product and when cold process is the better choice.

The same reaction, with heat after trace

Saponification is the reaction between oils and sodium hydroxide that makes soap and glycerin; the Cold Process Soapmaking Course, Module 1, explains it. Kevin Dunn's soap research, published on a supplier's blog, makes the point that "hot" and "cold" process differ by technique rather than by temperature: in hot process, heat is applied to the mixture after the oils and lye are combined, typically until the soap reaches gel and the reaction is complete; in cold process, no outside heat is applied after mixing, and most of the reaction happens in the mould [S29].

Heat speeds the reaction a great deal. In Dunn's measurements on a four-oil soap at 33% lye with no lye discount, held at a constant temperature, saponification was complete after a little more than an hour at 70 °C (158 °F) and after two hours at 60 °C (140 °F), while at 50 °C (122 °F) the soap was still alkaline well beyond four hours [S28]. Supplier tutorials hold the soap at or above about 71 °C (160 °F) by slow cooker or oven to speed the reaction up [S30][S31].

Time to complete saponification at constant temperature (Dunn's measurements)Four-oil soap, 33% lye, no discount, held at a steady temperature; hours70 °C (158 °F)a little more than 1 hour60 °C (140 °F)2 hours50 °C (122 °F)still alkaline beyond 4 hours0 h1 h2 h3 h4 h5 hDrawn from the figures stated in the text of [S28], not redrawn from its graph. One recipe at one water level; not a cook time for your batch.
Heat speeds saponification strongly: about an hour at 70 °C, two hours at 60 °C, and more than four hours at 50 °C in one recipe held at a steady temperature [S28]. Not a cook time for your batch.Source: Chart drawn for this course from the figures stated in the text of [S28] (not redrawn from its graph).
Cold process and hot process: the same start, a different finishWeigh and checkrecipe (same lye)Lye into water(same safety)Oils + lyeto traceSAME IN BOTHPour into mouldsaponifies in the mouldCure: steady weightand at least 4 weeksCOLD PROCESSCook in the potprobe log, attendedProtocolpassesOil, colour,fragrance; mouldHOT PROCESSthen cure: steady weight and at least 4 weeks (same release rule)Technique difference after mixing [S29]; cook held at or above about 71 °C in supplier methods [S30][S31]; release rule from Module 9.
Hot and cold process share everything up to trace. Hot process then cooks the batter until the completion protocol passes, adds the after-cook ingredients and moulds; both use the same release rule in this course [S29].Source: Diagram drawn for this course (vector) from the Module 1 text and its sources [S29][S30][S31]; release rule from Module 9 (course rule).

Those measurements were made on one recipe, held at a steady temperature; a real hot process batch is wetter, rises and falls in temperature, and loses water. They show the direction, not a cook time for your batch. Module 6 turns them into the course's completion protocol.

Side by side

Cold process Hot process
Where saponification finishes Mostly in the mould, over a day or two [S38] In the pot, before moulding [S29]
Water Course window 28–40% lye concentration (Cold Process Soapmaking Course) Often about 25% (3 : 1 water to lye) to allow for evaporation [S36]; this course uses 25–33%
Texture in the mould Smooth, pourable batter Thick and rustic, like mashed potatoes [S30][S31]
Design Fine swirls and very fluid designs Glopped layers, spoon swirls; fluid hot process allows simple swirls but not cold process detail [S34]
Fragrance Added to the batter before or at trace Added after the cook [S30][S32][S33]; in this course only below its flash point (HR-3)
Superfat Lye discount Lye discount, after-cook oil, or both; the course uses both (Module 4)
Cure At least 4 weeks and a steady weight (Cold Process Soapmaking Course) Sources range from "use right away" to 6 weeks [S30][S31][S32][S34][S38]; this course: steady weight and at least 4 weeks
Records Batch Log Cook Log: the Batch Log plus temperatures, completion checks and after-cook additions (Module 6)
Extra hazards Lye, raw batter Lye, raw batter, plus hot caustic batter, steam, boil-overs and appliances (Module 2)

What does not change

  • The lye calculation. Each oil needs the same lye whether you cook it or not; the shop calculator works it out from SAP values and the 1.403 KOH-to-NaOH ratio [S1].
  • The 1% superfat floor. The calculator calls superfat your safety margin and says to keep it above 1% [S1]. The course's house rules discard any batch whose recorded superfat is below 1%.
  • Protective equipment, lye handling and first aid. Goggles, gloves and long sleeves; lye into cold water; flush skin and eyes for at least 60 minutes and get to hospital [S2]. Module 2 restates every rule.
  • The discard rules. No reuse of failed or lye-heavy batches; discard at pH 11 or more on the lather or a recorded superfat below 1% (house rules).
  • The regulatory duties. Hot process soap is a cosmetic like any other: the Cosmetic Regulations' labelling and notification rules apply in full [S53]. Module 11 covers what hot process changes.

"Cooked" is not "milder", and not automatically safe

Two beliefs about hot process soap are common online. Neither holds up.

"Hot process soap is gentler." A double-blind study of 41 adults compared natural soaps made by cold and by hot process and found that both raised the skin's surface pH immediately, with the rise lasting up to 30 minutes [S47]. The method does not make soap gentle. This course never presents "hot process" as a skin benefit (the course's cautious interpretation, Module 11).

"Once it's cooked, it's safe." Only if the cook really finished, and the recipe was right in the first place. At trace, about 90–95% of the lye is still unreacted in Dunn's measurements [S28]. An undercooked batch, or a batch with a weighing error, still holds free lye, and a batch can look finished at the edges while the centre is not (Module 6). Sodium hydroxide burns skin and eyes [S2].

When to choose hot process, and when not

Hot process suits:

  • Fragrances that misbehave in cold process. Some fragrances accelerate, seize or separate cold process batter [S40]; one supplier notes that fragrance oils that sometimes seize cold process soap will generally work in hot process, because they go in after the cook [S33].
  • Rustic designs: chunky textures, glopped layers, textured tops [S30][S31].
  • Unmoulding sooner. Supplier tutorials unmould and cut after 1–2 days [S30][S32]. This does not mean selling sooner: the course's release rule is the same four weeks and steady weight as cold process (Module 9).
  • Rescuing a seized or separated cold process batch within 24 hours, when the weights are verified correct (Module 10, house rule HR-8) [S40].

Cold process is better for:

  • fine swirls, thin pour techniques and anything that needs a long time at a thin trace [S34];
  • a smooth, glossy top;
  • makers who cannot give a batch two to three hours of uninterrupted attention (the cook must be attended from start to finish, house rule HR-4).

A quick self-check before you start

Answer these honestly before you buy anything for hot process:

  1. Can you make a correctly weighed, correctly calculated cold process batch, and recalculate its superfat from actual weights?
  2. Can you keep children and pets out of the room for two to three hours at a time?
  3. Will you stay beside a hot cooker for the whole cook, and switch it off for every interruption?
  4. Do you have, or will you buy, a stainless steel vessel big enough that your batch fills half or less, and a probe thermometer you can check in ice water?
  5. Will you wait at least four weeks and a steady weight before using or selling the bars?

If any answer is no, start with the Cold Process Soapmaking Course or solve that point first. Module 2 of this course, which is free, sets out every hazard the cook adds.

What this course does not cover

  • Liquid (potassium hydroxide) soap. It is cooked too, but it is a different product with its own calculations and dilution; it belongs to a separate Liquid Soap course.
  • Rebatching and hand-milling as product methods. These melt finished soap and reshape it; they are not hot process. Rebatching a lye-heavy batch is never allowed (house rule).
  • Cook methods other than the slow cooker, oven and double boiler. No microwave, pressure cooker, sous vide bag, direct burner or open flame (house rule HR-9, Module 5).
  • Dairy in hot process. Some tutorials stir in dairy such as yogurt after the cook [S34]; this course leaves dairy out of all formulas and projects (Module 7 explains why).
  • New regulatory teaching. The full rules are in the Cold Process Soapmaking Course, Modules 16–19, and Selling Handmade Cosmetics in Canada; Module 11 covers what hot process changes.

The course at a glance

Section Modules
Foundations (free) 1 What changes · 2 Lye, heat and steam safety (safety gate)
Recipe and equipment 3 Equipment and set-ups · 4 Formulating for hot process
The cook 5 Cook methods · 6 Cook stages and judging completion
Finishing 7 After the cook · 8 Smoother texture · 9 Moulding, cutting and curing
Fixing and selling 10 Troubleshooting · 11 Records, labelling and selling

Four self-assessed assignments (a recipe conversion, a cook log, a troubleshooting case file and a label check) and a final exam complete the course. The Certificate of Completion from Island Enchantments recognises that you finished the course; it is not a licence or a government approval.

Scenario: is hot process for Ruth?

Ruth makes cold process soap for a weekend craft table. Her favourite fragrance, a spicy blend, seizes in cold process every time, and her customers like rustic, chunky bars. She has a busy household and often gets interrupted. She hoped hot process would let her sell soap the week she made it.

Hot process suits her fragrance and her style: the fragrance goes in after the cook, below its flash point, and rustic texture is natural [S30][S33]. But two things need planning. She will need a two-to-three-hour window with the house quiet, because the cook is attended from start to finish and children and pets stay out of the room (Module 2). And under the course's release rule, she still cures for at least four weeks to a steady weight before selling (Module 9).

Key terms

  • Hot process: soapmaking in which heat is applied after trace so saponification finishes in the pot, before moulding [S29].
  • Cold process: soapmaking in which no outside heat is applied after mixing and most of the reaction happens in the mould [S29].
  • Cook: the period of applied heat after trace, until the completion protocol passes.
  • Completion protocol: the course's four checks for judging that the cook is finished, with no zap test (Module 6).
  • After-cook addition: anything added once the cook is complete, such as superfat oil, colour and fragrance.
  • House rule: a course rule stricter than at least one published source (Module 2).

Summary

Hot process is cold process with heat applied after trace so the reaction finishes in the pot [S29]; heat speeds saponification strongly [S28]. It usually needs more water (about 25% lye concentration [S36]; 25–33% in this course), gives a rustic texture [S30][S31], suits fragrances that misbehave in cold process [S33][S40], and adds fragrance and superfat oil after the cook. The lye calculation, the 1% floor [S1], the safety rules [S2], the discard rules and the regulatory duties [S53] do not change. Cooked soap is not automatically milder [S47] or safe: an incomplete cook leaves free lye [S28], so this course never uses the zap test and judges completion by its protocol. Cure is to a steady weight and at least four weeks, as for cold process.

© 2026 Island Enchantments. For your personal learning only; do not copy or share (Academy Terms, section A8). General information, not legal, medical or other expert advice. Information current as of 2026-11-11; check official sources before relying on it. In an emergency call 9-1-1. Poison centre: anywhere in Canada 1-844-764-7669 (1-844 POISON-X); BC 1-800-567-8911; Québec 1-800-463-5060.

Sources cited

  • S1 Island Enchantments Soap Calculator: page text and calculator script read as text (hot process option: lye at full saponification for the base oils, after-cook oil = total oils x superfat %; water = lye x (100 - concentration) / concentration; warning below 25% and above 40% NaOH concentration; 1.403 KOH:NaOH ratio; option text on 2026-11-11 says the extra oil "does not stay a separate superfat over time: what counts is the total superfat of the bar", with the calculation unchanged. Nothing typed or submitted.
    Tier B · Island Enchantments x Fernquill Studio · retrieved 2026-11-11
    https://islandenchantments.com/pages/soap-calculator
  • S2 OSH Answers Chemical Profile: Sodium Hydroxide (fact sheet revised 2023-01-29): skin and eye first aid flush at least 60 minutes, do not interrupt, hospital; never delay flushing for contact lenses; always add corrosives slowly to cold water; reacts violently with water, acids, aluminum (hydrogen); corrosive to aluminum alloys and carbon steel; store in original labelled container.
    Tier A · Canadian Centre for Occupational Health and Safety (CCOHS) · retrieved 2026-11-11
    https://www.ccohs.ca/oshanswers/chemicals/chem_profiles/sodium_hydroxide.html
  • S28 Hot Stuff (Kevin Dunn, 2025-12-15): 39 olive / 28 coconut / 28 palm / 5 castor at 33% lye, no discount; trace after 22, 11 and 4 minutes at 40, 50 and 60 C; held at constant temperature, saponification complete after a little more than an hour at 70 C and after two hours at 60 C, still alkaline beyond four hours at 50 C; about 90-95% of the NaOH unreacted at trace.
    Tier B · Wholesale Supplies Plus (supplier blog, author Kevin Dunn) · retrieved 2026-11-11
    https://www.wholesalesuppliesplus.com/blogs/articles/hotstuff
  • S29 Time and Temperature (2025-12-11; data by students supervised by Kevin Dunn): hot and cold process differ by technique; HP heats after mixing, typically until gel and complete saponification; same blend gels at 71 C (160 F) at 33% lye and 87 C (189 F) at 40%; gel temperature rises with lye concentration; temperature profile as a batch record.
    Tier B · Wholesale Supplies Plus (supplier blog) · retrieved 2026-11-11
    https://www.wholesalesuppliesplus.com/blogs/articles/time-and-temperature
  • S30 Hot Process Series: Crock Pot Camo (2012-12-13): crock pot holds soap at or above 160 F; half full or less; low setting, 15-minute checks; batch may climb, do not leave unattended in the first 30 minutes, off the heat and stir, never grab boiling soap; champagne bubbles; mashed-potato texture; pH strip below 10; soap leaves the pot at about 160-180 F; moulds that handle that; separate crock pot as the GMP choice; 1-2 days in mould; usable at once, better after about 4 more weeks.
    Tier B · Soap Queen (Bramble Berry) · retrieved 2026-11-11
    https://soapqueen.com/bath-and-body-tutorials/cold-process-soap/hot-process-series-crock-pot-camo/
  • S31 Hot Process Series: Oven Process Layers (2012-12-21): oven holds soap at or above 160 F; preheat 170 F; racks low and away from elements; foil or tray below for overflow; stainless oven-safe vessel; half full; 15-minute checks; partial gel at 45 minutes, full gel at 60 minutes in that batch; hot-pad gloves; clays dispersed in water (clays absorb water and can crack soap); more liquid at the end = smoother but longer cure; orange EO may not survive the heat; moulds must sustain 170 F
    Tier B · Soap Queen (Bramble Berry) · retrieved 2026-11-11
    https://soapqueen.com/bath-and-body-tutorials/cold-process-soap/hot-process-series-oven-process-layers/
  • S32 Snowdrop Hot Process Soap Tutorial (2016-11-01): half full or less because soap expands; flatter or larger vessels cook faster; about 12-15 minutes total for that small batch; glossy Vaseline-like texture; "tricky to know for sure"; spoonful in distilled water, pH strip below 10; sodium lactate 3% of oils in cooled lye; low setting, check at about 10 minutes; gloves; at least 2 weeks cure.
    Tier B · Soap Queen (Bramble Berry) · retrieved 2026-11-11
    https://soapqueen.com/bath-and-body-tutorials/snowdrop-hot-process-soap-tutorial/
  • S33 Hot Process Soap Making: double boiler with water at a slow boil, spacer under the inner pot, covered, 1.5-2 hours, check and top up the water, translucency as a sign; fragrance and specialty oils after the cook; thins with isopropyl alcohol or vodka and pours into plastic moulds (neither adopted)
    Tier B · Voyageur Soap & Candle (supplier, Surrey BC) · retrieved 2026-11-11
    https://www.voyageursoapandcandle.com/pages/hot-process-soap-making
  • S34 Fluid Hot Process Soap Tutorial and Recipe (A. Aaron, 2016-11-03): more water (2.5 x lye) gives more fluid soap but risks shrinkage; sodium lactate 1 tsp per lb oils (too much = crumbly); sugar 1 tsp per lb in cooled lye; yogurt after the cook; plastic wrap under the lid and little stirring limit evaporation; high setting; edges translucent first; zap test at the end (not adopted); cut after about 4 hours; 2-3 week cure
    Tier B · Lovin Soap Studio · retrieved 2026-11-11
    https://lovinsoap.com/2016/11/fluid-hot-process-soap-tutorial-recipe-fluid-hp/
  • S35 Zap Test: strips and phenolphthalein "notoriously inaccurate"; a pH meter only if maintained, calibrated and used correctly; skin-safe soap about pH 9.5-11.5 depending on fatty acids; total alkalinity test is the industry standard (zap test described, not used here).
    Tier B · Classic Bells (soapmaking educator pages) · retrieved 2026-11-11
    https://classicbells.com/soap/zapTest.asp
  • S36 Sous Vide for Soap Makers: many HP recipes use 25% lye (3:1 water:lye) to allow for evaporation; bagged batter in water at 80 C on a burner, about 1 hour; no extra water needed in a sealed bag (method not taught)
    Tier B · Classic Bells · retrieved 2026-11-11
    https://classicbells.com/soap/sousVide.asp
  • S38 Curing soap: HP soap usually has more water so it takes longer to reach a steady weight; some makers cure HP at least 6 weeks; weigh a bar every few days for 6-8 weeks; by 4-8 weeks loss slows to a crawl with 50-70% of the water left; HP only speeds saponification
    Tier B · Classic Bells · retrieved 2026-11-11
    https://classicbells.com/soap/cure.asp
  • S40 How to Work with Misbehaving Fragrances: seized or separated soap can be rescued up to 24 hours later by hot process in a stainless pot three times the batch size, with safety gear (on the stovetop, which this course does not use).
    Tier B · Bramble Berry · retrieved 2026-11-11
    https://www.brambleberry.com/how-to/how-to-work-with-misbehaving-fragrances.html
  • S47 Zdrada-Nowak J, Aniolkowska S, Deska M. Evaluating skin acid-base balance after application of cold-processed and hot-processed natural soaps: a double-blind pH monitoring study. Cosmetics 2025;12(3):120 (abstract and introduction read): 41 adults; both soap types raised skin surface pH immediately, lasting up to 30 minutes.
    Tier A · MDPI (peer-reviewed journal) · retrieved 2026-11-11
    https://www.mdpi.com/2079-9284/12/3/120
  • S53 Cosmetic Regulations, C.R.C., c. 869 (current to 2026-10-19, last amended 2026-04-12): s. 2 "ingredient" excludes substances used in preparation that are not present in the final product as a result of the chemical process; INCI name definition; s. 21.2 list of ingredients on the outer label by INCI name, botanicals by at least genus and species; s. 21.3 chemical name if no INCI name; descending order by weight, 1% or less and colourants in any order after; "parfum"/"aroma"; fragrance allergens listed above 0.01% in rinse-off and 0.001% in leave-on products; s. 21.4 (as amended by SOR/2024-63; allergen provisions in force 2026-04-12): the fragrance allergens are those the European Restricted Substances List (Annex III of EU Regulation 1223/2009) says must be indicated, with that list's transition dates; s. 30 notification within 10 days after first sale, with INCI list and exact concentration or range code (table of 13 ranges); s. 31 revised notification within 10 days of a change.
    Tier A · Department of Justice Canada (Justice Laws) · retrieved 2026-11-11
    https://laws-lois.justice.gc.ca/eng/regulations/C.R.C.,_c._869/FullText.html

Module quiz

10 questions drawn at random from a bank of 25. Pass mark 80%. Retake as often as you like.

Progress is saved in this browser.

The Island Enchantments Academy offers self-paced courses for personal and small-business learning. It is not a certified or registered private training institution under British Columbia's Private Training Act. Its courses are not accredited and do not lead to a diploma, degree or professional licence.

Courses created by Fernquill Studio for Island Enchantments

Island Enchantments · Victoria, BC · islandenchantments.com