Hot process soap is cold process soap that you keep cooking. Everything that makes lye dangerous is still there, and the cook adds heat, steam, rising batter and appliances that stay hot for an hour or more. This module is always free. You must pass its quiz at 100% before the rest of the course opens, and you will be asked to tick the Safety Acknowledgment, Assumption of Risk and Release, shown in full below, before Module 3. Nothing in this module is hidden behind it.
This module builds on the Cold Process Soapmaking Course, Module 2 (Lye Safety and Your Workspace), also free. Every rule you need is restated here.
What you'll learn
- LO2.1 Apply the Cold Process Soapmaking Course lye rules (protective equipment, lye into water, storage, children and pets, no aluminium, no glass for lye, dedicated tools) to a cook that runs for an hour or more.
- LO2.2 Identify the hazards the cook adds: hot caustic batter, steam and hot condensate, rising and boiling-over batter, hot vessels and lids, a double boiler boiling dry, oven and stovetop fire, cords and alcohol near heat.
- LO2.3 Give correct first aid for hot batter on skin or in the eyes (the lye protocol: flush 60 minutes, poison centre, hospital), for scent oil alone in the eye, and for a steam or water scald.
- LO2.4 Follow the house rules for hot process: half-full limit, attended cook, no alcohol near heat, fragrance below its flash point, dedicated equipment, no zap test, and goggles and gloves for scent oils and hot oils.
- LO2.5 Set up, run and shut down a hot process workspace, including what to do when interrupted or when the power fails.
Part A: the lye rules, restated
Why the rules still apply after trace
At trace the lye is not "used up". In measurements on a standard four-oil soap, about 90% of the sodium hydroxide was still unreacted when a batch at 50 °C (122 °F) reached trace, and about 95% when a batch at 60 °C (140 °F) did [S28]. Held at a steady 70 °C (158 °F), the same soap took a little more than an hour to finish; at 50 °C it was still alkaline after four hours [S28]. So for most of a hot process cook, the pot holds a hot mixture that is still strongly caustic. Sodium hydroxide causes severe skin burns and eye damage [S2].
The core rules
- Protective equipment. Chemical-splash goggles, chemical-resistant gloves and long sleeves every time you handle lye, lye solution or batter [S2][S30][S32]. Chemical-splash goggles are non-vented or indirect-vented and seal to the face [S66]. Add an apron and closed shoes.
- Lye into water, never water into lye. Add the lye slowly to cold water, stirring [S2]. Water poured onto solid lye causes violent frothing and spattering [S2].
- Ventilation. Mix the lye solution where air moves, by an open window or under a fan [S5][S30][S34].
- Storage. Keep lye tightly closed in its original, labelled container, somewhere cool and dry, away from acids and metals [S2][S5]. Keep it out of sight and out of reach of children and pets [S5]. Child-resistant packaging is not child-proof [S5].
- Metals. Never let lye or batter touch aluminium: it reacts and gives off flammable hydrogen gas [S2]. Sodium hydroxide also corrodes aluminium alloys and carbon steel [S2].
- No glass for lye. Alkaline solutions attack all glass, and even heat-resistant borosilicate glass is only moderately resistant [S12]. House rule: the course never mixes, stores or cooks lye or batter in glass, stricter than suppliers who accept heat-resistant glass.
- Dedicated tools. House rule: anything that has touched lye or raw soap never goes back to food use. For hot process this includes the cooker itself (house rule HR-5, below).
- Children and pets out of the room for the whole session, from weighing the lye to the end of cleanup [S30][S32]. In 2020, Canada's poison centres handled 215,589 cases, and more than a third involved a child aged five or under [S3].
Scent oils and hot oils
Scent goes in at the end of the cook (Module 7). One Academy rule covers it:
Lye courses (Cold Process, Hot Process, Liquid Soap). The chemical-splash goggles and chemical-resistant gloves you wear for lye meet this rule; keep them on when scent goes in. If you weigh scent before the lye work starts or after it is cleaned up, the rule above applies on its own.
Hot wax, butter and oil. You melt hard oils and butters for the cook (Module 5), often before the lye is out. Hot oil can spatter and cause severe burns [S6], and goggles are listed protection against molten splashes [S66]. Wear chemical-splash goggles whenever you heat, stir, pour or top up molten wax, melted butter or hot oil, and heat-resistant gloves to handle hot containers. Disposable gloves are not heat protection (house rule).
You at the bench (house rule). If you are pregnant or breastfeeding, the course's cautious position is that someone else does the essential-oil and fragrance-oil steps, or you make the batch unscented; if you have epilepsy or asthma, ask a health care provider before you handle these oils. The official cautions the course relies on are written for people who use a product, not for people who make one, so this is a precaution of the course, not a rule from Health Canada [S72].
Part B: hazards the cook adds
Hot caustic batter
Cooked soap leaves a slow cooker at about 71–82 °C (160–180 °F) in one supplier's tutorial [S30], and supplier methods hold the soap at or above about 71 °C (160 °F) during the cook [S30][S31]. Batter at that temperature can cause a thermal burn and a chemical burn at the same time: hot liquids and steam cause thermal burns [S9][S10], and sodium hydroxide causes a chemical burn that needs long flushing [S2]. The lye protocol wins (first aid, below).
Steam and hot condensate
Keep a slow cooker's lid in place and lift it only to stir or check [S11]. Lifting it releases steam and hot drops from under the lid at once, and steam scalds as hot water does [S9][S10]. That condensate has run over the batter and can carry soap with it.
Course practice for lids: lift the far edge first so steam vents away from you, hold the lid over the pot a moment so condensate drips back, and keep your face back. Put the lid down on a heat-resistant surface [S6], wet side up.
Rising batter and boil-overs
Soon after trace, some batches grow with fine bubbles and try to climb out of the pot. One supplier calls these "champagne bubbles", the main reason to fill no more than half full [S30]; another supplier's batch visibly expanded in a two-quart slow cooker [S32]. If the batter climbs, turn the heat off (or take the pot off the heat), stir hard with gloves on, and never grab boiling soap [S30][S32]. Natural sugars, fruit purées and alcohol can superheat soap batter and cause a "soap volcano" [S41].
Hot vessels, lids, racks and doors
The vessel, lid, cooker casing, oven racks and door, and a double boiler's water bath all get hot. One supplier lifts the vessel from the oven only with hot-pad gloves [S31]; HealthLinkBC lists hot elements and oven doors as burn hazards [S8]. Oven mitts go over your chemical gloves, never instead of them.
A double boiler boiling dry
In the double-boiler method the soap pot sits in a larger pot of water at a slow boil for 1½–2 hours, and the supplier says to check and top up the water [S33]. Once it is gone, nothing limits how hot the inner pot gets. Course practice: top up only with hot water from a kettle, poured slowly down the side of the outer pot, away from the soap pot.
Cords and appliances
A child who pulls a slow cooker's cord can bring it down and be burned: keep cords out of reach and appliances back from the counter edge [S8][S7]. Keep cords away from heat and water, replace worn or frayed ones, and use only plug-in appliances with a recognised Canadian safety mark such as CSA, cUL or cETL [S7].
Fire: hot oil and flammable liquids
Unattended cooking is a leading cause of cooking fires; never leave cooking appliances unattended [S6]. If oil catches fire, turn off the heat if that is safe [S69], use a kitchen extinguisher or cover it with a metal lid, get everyone out and call 9-1-1; never use water on an oil fire [S6].
Alcohol is the other fire risk at the cooker. Isopropyl alcohol has a flash point of 11.7 °C (53 °F) and its vapour forms explosive mixtures with air [S14]; ethanol (in vodka and other spirits) has a flash point of 12.0 °C (54 °F) [S15]. The flash point is the lowest temperature at which a liquid gives off enough vapour to catch fire from a spark or flame [S17], so both alcohols are well above it at room temperature. Their vapours are heavier than air and can travel to an ignition source; keep flammable products away from heat and hot surfaces [S18]. One supplier thins hot soap with isopropyl alcohol or vodka [S33]; this course never does (HR-2, below).
Many essential and fragrance oils are flammable too: CCOHS classes any liquid with a flash point of 93 °C (199 °F) or less as flammable [S17], and d-limonene forms explosive vapour and air mixtures above 48 °C (118 °F) [S16]. End-of-cook batter is hotter than that, so HR-3 waits for it to cool (Module 7).
First aid
Why batter gets the lye protocol
Cooling hot batter for a few minutes, as for a scald, would leave the chemical burn untreated. CCOHS says to flush sodium hydroxide from skin for at least 60 minutes without interruption and get to hospital [S2]. HealthLinkBC's general chemical-burn advice is at least 20 minutes [S9]; the course follows the longer CCOHS time, and the water cools the heat injury too.
If you are not sure whether a burn involved batter, treat it as if it did. Condensate dripping from a lid that has been over the batter counts as batter.
Steam and hot-water scalds
Cool a scald from steam or clean hot water under cool running water: HealthLinkBC gives 10 to 20 minutes for an adult [S9], the NHS 20 minutes [S10]; the course uses 20 minutes. Never put ice, butter, oil or cream on a burn [S8][S9][S10]. Remove hot, wet clothing unless it is stuck to the skin [S8]. Large burns, burns to the face, hands, feet or groin, and any blistering need medical care; cool a large burn, then call 9-1-1 [S8].
Who to call
Call 9-1-1 for anyone unconscious, having a seizure, trouble breathing or chest pain [S4], and for lye or batter in the eye or swallowed, while flushing continues [S2][S4]. For lye or batter on the skin, call a poison centre right away, then go to hospital [S2]. In any doubt, call a poison centre [S4][S5].
- Anywhere in Canada: 1-844-POISON-X (1-844-764-7669), which routes you to your local poison centre [S3]. In Quebec, the Centre antipoison du Québec is 1-800-463-5060 [S3].
- British Columbia (BC Drug and Poison Information Centre): 1-800-567-8911 or 604-682-5050, 24 hours [S4].
The course house rules for hot process
The Cold Process Soapmaking Course has house rules that carry over unchanged: no zap (tongue) test; no reuse of a failed or lye-heavy batch; no heating pads; no glass for mixing or storing lye; no home neutralising of leftover lye; tools never return to food use; discard any batch whose recorded superfat is below 1% or whose lather reads pH 11 or more on a strip. This course adds nine. Each is a house rule; the table names the source it is stricter than.
| # | House rule | Stricter than |
|---|---|---|
| HR-1 | No zap test at the end of the cook either. Completion is judged by the course protocol in Module 6. | One educator ends the cook with a zap test [S34]; another describes the zap test as acceptable [S35] |
| HR-2 | No alcohol (isopropyl, vodka or any spirit) to thin, spray or treat hot soap, and no open alcohol near the cooker or oven. | A supplier that thins hot soap with isopropyl alcohol or vodka [S33] |
| HR-3 | Fragrance and essential oils go in only after the batter has cooled below the flash point on that oil's safety data sheet. | Supplier tutorials that add fragrance as soon as the cook ends [S30][S32] |
| HR-4 | Fill to half the vessel or less, and attend the cook from start to finish. Switch the heat off before leaving the room for any reason. | Supplier tutorials that say not to leave the soap in the first 30 minutes [S30][S32]; food guidance that lets a slow cooker run while you are out [S11]. Health Canada: never leave cooking unattended [S6] |
| HR-5 | A dedicated cooker, pot or vessel, labelled and never returned to food use. | A supplier that calls sharing with food one "school of thought" [S30] |
| HR-6 | Hot soap never goes into PVC, acrylic or thin plastic moulds. (Module 3) | A supplier that pours hot soap into plastic moulds [S33] |
| HR-7 | Stainless steel cooking vessels only, for every method. No glazed stoneware crocks, no glass, no aluminium. | Most slow-cooker tutorials, which use the stoneware crock |
| HR-8 | Hot process rescue of a cold process batch only when the weights are verified correct and within 24 hours; never for lye-heavy soap. (Module 10) | Rescue advice that does not check the weights first |
| HR-9 | Only the three taught methods: slow cooker, oven, double boiler. No microwave, pressure cooker, sous vide bag, direct burner or open flame. (Module 5) | An educator's sous vide method and other stovetop practice |
Why HR-7? Stainless steel types 304 and 316 resist sodium hydroxide at any concentration below 80 °C (176 °F) and are fine up to 95 °C (203 °F) in service [S13]; no maker's data on stoneware glazes was found, and alkali attacks all glass [S12].
Before, during and after the cook
Set-up
- Pick a time when nobody will need you for about three hours and children and pets can be kept out of the room [S30][S32].
- Gear: chemical-splash goggles, chemical-resistant gloves, long sleeves, apron, closed shoes, oven mitts that fit over your gloves, and disposable nitrile gloves for any scent weighed outside the lye work.
- Inspect the equipment (Module 3): stainless vessel without pitting, lid, unfrayed cord [S7], probe thermometer checked in ice water.
- Place the cooker well back from the counter edge with its cord out of reach [S7][S8], away from the sink and anything flammable.
- Clear away alcohol, paper towels and clutter [S18]. Know where your fire extinguisher and a metal lid are [S6].
- Keep a clear path to running water and the phone, with the poison centre number posted [S3][S4].
- Weigh everything before you mix, and check the recipe against a lye calculator (Module 4).
The attended cook
- Stay beside the pot from the moment the heat goes on until it is off and the soap is in the mould (HR-4); Health Canada says to turn off the heat first if you have to leave [S6].
- Check, stir and log every 10–15 minutes [S30][S32], more often in the first 30 minutes, when rising is most likely [S30].
- Keep the lid on between checks [S11], and lift it the safe way.
- Never lean over an open pot.
Interruptions and power cuts
The doorbell rings or a child calls: switch the heat off first, then go (HR-4) [S6], leaving the lid on.
If the power fails during the cook (course practice; food-safety power-cut rules are written for food [S11]):
- Leave the lid on and keep children and pets away. The batter is still caustic.
- Do not carry a hot, full vessel somewhere else.
- Log the time and the last probe reading.
- When the power returns, check that the batter has not set, resume, and start the completion protocol's time count again from zero (Module 6).
- If the batch has set hard or the power stays off for more than 24 hours, do not reheat it. Cover it, label it "CAUSTIC: UNFINISHED SOAP", lock it away and deal with it as Module 10 describes.
Shutdown and cleanup
- Switch off and unplug the cooker before you mould. Put the hot vessel on a heat-resistant surface [S6].
- Residue on the vessel, spatulas and lid is caustic. Keep gloves and goggles on while you clean.
- Let residue cool and set, scrape it into a labelled bag, then wash tools with hot soapy water, in gloves.
- Never put soap tools or the cooker in the food cupboard (HR-5). Wipe the counter, then remove gloves and wash your hands.
Scenario: putting it together
Priya, a fictional maker, is cooking in a stainless slow-cooker insert. Twenty minutes in, she lifts the lid towards her face; steam fogs her goggles and a drop of condensate lands on her wrist above her glove. Then the batter starts to rise. What should she do, in order?
She turns the heat off and, gloves on, stirs the batter down without grabbing at it [S30][S32]. The drop came off the lid over the batter, so it counts as batter: with the heat off (HR-4), she flushes the spot for at least 60 minutes, calls the poison centre and gets medical care [S2]. Next time she lifts the far edge of the lid first and wears a sleeve that overlaps her glove.
Key terms
- Hot caustic batter: soap batter during the cook; hot and still strongly alkaline, so it can cause thermal and chemical burns together.
- Lye protocol: flush at least 60 minutes, poison centre, hospital (9-1-1 for eyes or swallowing) [S2][S4].
Summary
For most of the cook the batter is hot and still caustic [S28][S2], so every splash, including lid condensate, gets the lye protocol: flush at least 60 minutes, poison centre and hospital, or 9-1-1 for eyes [S2][S4]. Only a clean steam or water scald gets 20 minutes of cool running water [S9][S10]; only scent oil alone, from a clean bottle, gets the 15-minute lukewarm rinse [S68], and if in doubt, follow the lye steps. Wear chemical-splash goggles and gloves for lye, scent oils and hot oils [S66]. Fill half full or less, stay beside the cook and switch off to step away (HR-4) [S6][S30]. No alcohol near heat (HR-2) [S14][S15], scent below its flash point (HR-3) [S17], dedicated stainless vessels (HR-5, HR-7) [S13], no zap test (HR-1), and no children or pets in the room [S3][S8].